Take advantage of our huge selection of patterns & colors! Please be sure to check out the easy application instructions below!
All you need is a plotter or cutter! All Patterns are printed with a large format Roland printer that uses Eco-solvent genuine inks. Permanent Adhesive Craft Vinyl (Outdoor/Indoor Vinyl).
Printable Oracal 651 - No Transfer Tape Provided. Great to use on glass, metal, plastic, and much more! Please clean surface before use!Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a transfer tape to transfer design off of the backing and place on your smooth & clean surface. Weatherproof / 4+ years durability. Reusable No Residue Non-Slip Removable Adhesive Craft Vinyl. Apply, Remove & Apply Again! Comparable to 3M - No Transfer Tape Provided. Weatherproof / 7+ years durability.
Iron on Heat Transfer Vinyl - For Any Garment or Fabric. Printed on Siser ColorPrint Easy (TTD High-Tack Mask Provided). Heat Transfer is printed without the carrier. Siser TTD Easy Mask is provided for application. After weeding excess vinyl, apply TTD Easy Mask to transfer design off of the backing and place on your garment face up.
Can be applied with a home iron and/or heat press. Cricut: Blade: Standard Setting: Iron On.Silhouette Cameo: Blade: Standard, 3 Material: Heat Transfer, Smooth Speed: 8 Force: 6. Scan N Cut: Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 1.
Roland GS/GX-24: Blade: 45° Gram Force: 80-90 Offset: 250 Speed: 25-50 cm/s. Graphtec: Blade: 45° Gram Force: 9 Tool: CB09U+0 Speed: 25 cm/s. MH, SC2, LP3, & Titan 1: Blade: 45°/60° Gram Force: 80-85 Speed: 300mm/s Blade Advancing Varies.
Titan 2 & 3 Blade: 45°/60° Gram Force: 60-65 Speed: 300mm/s Blade Advancing Varies. Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs. Application Instructions (home iron) Set iron dial between Cotton and Linen Cover design with Kraft paper or non-stick cover sheet Place on flat, hard surface (ironing board not recommended) Press iron with medium/firm pressure (do not slide iron) Press each section of design for 15 seconds If areas of design lift after application, replace cover sheet and re-press for 10 seconds Peel carrier hot or cold. Application Instructions (heat press) Cut material - don't mirror!Weed excess material Mask with TTD High Tack Mask Preheat garment for 2-3 seconds Apply design at 305°F/150°C Use medium pressure for 10-15 seconds Peel carrier hot or cold Cover and reheat for 2-3 seconds. Patterned Vinyls Apply to: 100% cotton Poly/cotton blends 100% polyester Leather Lycra®/spandex. Laundering: Wait 24 hours before 1st wash Machine wash cold / mild detergent Dry on normal dryer setting Do not dry clean Do not bleach. SIZE AND HOW TO APPLY. 1 Do not mirror 2 Cut on pattern 3 Weed excess vinyl 4 Apply and peel mask 5 Press.
1 Do not mirror 2 Cut on pattern 3 Weed excess vinyl 4 Apply and peel mask. Have your own patterns you want to print? The item "Ombre Marble Pattern HTV Siser & Adhesive Craft Vinyl Oracal FREE SHIPPING $20+" is in sale since Tuesday, September 1, 2020. This item is in the category "Crafts\Scrapbooking & Paper Crafts\Die Cutting & Embossing\Die Cutting Vinyl". The seller is "shopvinyl4u" and is located in Garden Grove, California.
This item can be shipped worldwide.